acceptable screws - eviltoast
  • Torx gang unite.

    We had our 20 y/o deck repaired and stained last year. I was chatting with the overseer about what he was going to do and the topic of screws came up; he said he was going to use Torx, and only ever used Torx anymore - I just about cheered.

    I’d been losing hope in humanity lately, but little signs of sanity like this, professionals finally getting rid of the hell-bits that are Phillips heads, lifts my heart and gives me hope.

    • wjrii@lemmy.world
      link
      fedilink
      English
      arrow-up
      3
      ·
      7 months ago

      These days, all but the cheapest outdoor-grade screws in the US are torx, generally with a bit thrown into the box that, while cheap, should work fine for a few boxes’ worth.

      • Freaking awesome. Better and better. We’ve finally fixed the screw heads, and pretty much also computer connectors (and small device chargers!) with USB-C. Just in time for the end of the world via total ecological collapse.

        Great times.

    • bonn2@lemm.ee
      link
      fedilink
      arrow-up
      3
      ·
      7 months ago

      I work at a big box hardware store, and I can confirm that almost all deck and structural screws are moving to torx. (much to the older generations dismay)

    • azertyfun@sh.itjust.works
      link
      fedilink
      English
      arrow-up
      1
      ·
      7 months ago

      I’ve heard that was more of a European thing, but the only two serious contenders are Pozidriv vs Torx for screws (and hex vs Allen for bolts).

      I just checked my local hardware store’s website, and out of the 176 kinds of 4/4.5mm screw boxes in their inventory, 74 are Torx, 55 are Pozidriv, and 38 are Phillips (ew).

      Either Torx or Pozidriv is fine when used properly, however most DIYers don’t understand the difference between PZ and PH and end up stripping their heads. Also it’s much harder to use the wrong-sized bit with Torx than PZ.

      So yeah, Torx wins in just about every category and other heads only get manufactured to appease old people and penny-pinchers.

      • That’s one of my issues with Pozi - it can be hard to see the markings, and not everyone has great eyesight. I mostly object to Phillips-related screws because there are so many variations that mostly look the same and require a table to differentiate. And none have the torque-transfer performance of Torx. Plus, you can use a hex head in a Torx bit in an emergency and you don’t much care about either the bit or the head.

    • dankm@lemmy.ca
      link
      fedilink
      arrow-up
      0
      ·
      7 months ago

      I’m not sure I’ve ever seen a philips or slotted deck screw. I have and have purchased many boxes of these things and they’ve always been nearly 100% Robertson. Is this a US thing?

      • Yes, and you’re Canadian. Robertson is the standard there, and while it’s used in other countries, not nearly as much.

        In the beginning was slotted heads, mainly because mass machining and casting wasn’t good enough to have more precise forms. Then came the Great Connector Wars, and in the US the Phillips head won and was standardized; almost every house built in the US in the past 80 years will be built with these (and nails). Slotted heads are much less common, but you find them in various specific places, like where the heads are visible and you want to hide the screw as much as economically possible.

        Canada, however, was smarter and standardized on the Robertson head; IIRC one reason for the divergence was the Phillips licensing cost. In any case, Robertson is superior to Phillips in most ways, except it’s even worse to dig out if it gets painted over.

        As machining improved, many attempts were made to improve on Phillips, which mostly amounted to polishing a turd; Robertson remained unchanged as it was already pretty good.

        Then came hex, which is great except it’s structurally pretty terrible for the head. Still, it can be seen as an improvement in Robertson, but not quite so good as to be worth all the retooling. Good enough that it’s probably the second, or at least third, most popular head in the US.

        Finally, someone did some fucking math and came up with Torx, which is provably and demonstrably superior to all other screw heads. It maximizes force transfer, and leaves more material in the head; it’s harder to strip out, and can be applied effectively to very small screw heads. There’s a security version, which was mostly useless (for intended purpose) the day after it was released, but beyond that, there’s no real improvement that can be made.

        The Phillips patents expired decades ago, so it’s holding on mainly from inertia. Commercial contractors don’t have much invested in it, because they have to literally buy boxes of replacement Phillips heads because of how shitty the design is and how often the heads break. While manufacturers have a steady stream of revenue from selling replacement Phillips tools that have broken, this is balanced by the mouth-watering prospect of every contractor in the US buying new Torx size-sets and high-end Torx tools. And the screw makers probably DGAF as they’ll sell screws either way; Torx screws might be a little more expensive - they used to be, but I haven’t compared lately.

        Canada may just motor on using Robertson; there’s less incentive for them to retool since Robertson isn’t nearly as crappy as Phillips, so the cost/benefit to upgrade to Torx is less compelling. But who knows?