Route domain name to Docker containers on Synology NAS? - eviltoast

I’m sure I’m massively overthinking this, but any help would be greatly appreciated.

I have a domain name that I bought through NameCheap and I’ve pointed it to Cloudflare (i.e. updated the name servers). I have a Synology NAS on which I run Docker and a few containers. Up until now I’ve done this using IP addresses and ports to access everything (I have a Homepage container running and just link to everything from there).

But I want to setup SSL and start running Vaultwarden, hence purchasing a domain name to make it all easier.

I tried creating an A record in Cloudflare to point to the internal IP of my NAS (and obviously, this couldn’t be orange-clouded through CF because it’s internal to my LAN). I’m very reluctant to point the A record to the external IP of my NAS (which, for added headache is dynamic, so I’d need to get some kind of DDNS) because I don’t want to expose everything on my NAS to the Internet. In actual fact, I’m not precious about accessing any of this stuff over the internet - if I need remote access I have a Tailscale container running that I can connect to (more on that later in the post). The domain name was purely for ease of setting up SSL and Vaultwarden.

So I guess my questions are:

  • What is the best way to go about this - do I create a DDNS on the NAS and point that external IP address to my domain in Cloudflare, then use Traefik to just expose the containers I want to have access to using subdomains?
  • If so, then how do I know that all other ports aren’t accessible (I assume because I’m only going to expose ports 80 and 443 in Traefik?)
  • What do other people see (i.e. outside my network) if they go to my domain? How do I ensure they can’t access my NAS and see some kind of page?
  • Is there a benefit to using Cloudflare?
  • How would Pi-hole and local DNS fit into this? I guess I could point my router at Pi-hole for DNS and create my A records on Pi-hole for all my subdomains - but what do I need to setup initially in Cloudflare?
  • I also have a RPi that has a (very basic) website on it - how do I setup an A record to have Cloudflare point a sub-domain to the Pi’s IP address?
  • Going back to the Tailscale thing - is it possible to point the domain to the IP address of the Tailscale container, so that the domain is only accessible when I switch on the Tailscale VPN? Is this a good idea/bad idea? Is there a better way to do it?

I’m sure these are all noob-type questions, but for the past 6-7 years I’ve purely used this internally using IP:port combinations, so never had to worry about domain names and external exposure, etc.

Many thanks in advance!

  • schmurnan@lemmy.worldOPEnglish
    1·
    1 year ago

    Just a quick update on where I’m up to…

    I’ve managed to get all my containers working behind the Traefik reverse proxy with SSL. I’ve also deployed a Cloudflare DDNS container in Docker and have linked the external IP address of my Synology NAS to Cloudflare. I haven’t port forwarded 80 and 443, though, so it’s not accessible over the internet. So I’ve added local DNS into Pi-hole so I can access all the containers using subdomains.

    I’ve also deployed an Authelia container and have started running through my containers adding 2FA in front of them all.

    I should probably point out at this juncture, that if I encounter any errors, the HTTP 404 page that I get is a Cloudflare one - I assume that’s expected behaviour?

    So, the final three bits I’m struggling with now are:

    • Pi-hole behind the reverse proxy
    • Portainer behind the reverse proxy
    • Accessing Vaultwarden over the internet (because as soon as I leave my house, if the vault hasn’t synced then I don’t have access to all my passwords) - unless anybody has a better suggestion?

    Portainer - I have no idea how I do it, because I use it to manage my containers, so don’t have the config for Portainer in Portainer (obviously). So if I screw up the config, how am I getting back in to Portainer to fix it?

    And the far more troubling one is Pi-hole. I just cannot get that thing working behind the reverse proxy.

    I’ve followed a few different guides (though none of them are recent), and the below is the latest docker-compose I have. It will bring up the login page, but when I login it keeps returning me back to the login page - it won’t go to the main admin page.

    version: "3.7"

services:
  pihole:
    container_name: pihole
    image: pihole/pihole:latest
    restart: unless-stopped
    networks:
      - medianet
      - npm_network
    ports:
      - 8008:80
      - 53:53/tcp
      - 53:53/udp
    environment:
      - TZ=Europe/London
      - WEBPASSWORD=xxxxxxxxxx
      - FTLCONF_LOCAL_IPV4=192.168.1.116
      - WEBTHEME=default-auto
      - DNSMASQ_LISTENING=ALL
      - VIRTUAL_HOST=pihole.mydomain.com
    volumes:
      - /path/to/pihole:/etc/pihole
      - /path/to/pihole/dnsmasq.d:/etc/dnsmasq.d
    cap_add:
      - NET_ADMIN
    labels:
      - traefik.enable=true
      - traefik.http.routers.pihole.entrypoints=http
      - traefik.http.routers.pihole.rule=Host(`pihole.mydomain.com`)
      - traefik.http.middlewares.pihole-https-redirect.redirectscheme.scheme=https
      - traefik.http.routers.pihole.middlewares=pihole-https-redirect
      - traefik.http.middlewares.pihole-addprefix.addprefix.prefix=/admin
      - traefik.http.routers.pihole.middlewares=pihole-addprefix
      - traefik.http.routers.pihole-secure.entrypoints=https
      - traefik.http.routers.pihole-secure.rule=Host(`pihole.mydomain.com`)
      - traefik.http.routers.pihole-secure.tls=true
      - traefik.http.routers.pihole-secure.service=pihole
      - traefik.http.services.pihole.loadbalancer.server.port=80

networks:
  medianet:
    external: true
  npm_network:
    external: true